In stock
SKU
LED Anti-Aging Device

LED Anti-Aging Device

$6,950.00
Rating:
93% of 100

S+ is an over the counter, LED infrared and radio frequency Anti-Aging device targeted to reduce the appearance of fine lines and wrinkles. The S+ device emits red and infrared energy rays into the skin which stimulate and rejuvenate skin cells to enhance the appearance of the skin.

The S+ LED Anti-Aging Device is a LED Light Photon Beauty Device that will revive, rejuvenate, and revitalize your skin for a flawless appearance inside-out. It unleashes the powers of advanced LED technology to assist in battling any visible signs of premature aging such as fine lines, wrinkles, marks, and blemishes, resulting in a rejuvenated, radiant, and youthful appearance.

Key Benefits:

  • • The S+ stimulates Collagen growth
  • • The S+ restores younger looking skin
  • • The S+ is best for providing a SPA like tightening and lifting effect


How to Use the S+:

Results vary by person, skin type, tone, the frequency of use and accuracy. A single treatment session can take up to 15-20 minutes. For optimal results, start with the radio frequency setting for 2-3 minutes to break down collagen. Follow treatment using the infrared setting. Gently and slowly glide the applicator over the desired treatment area. During the procedure, you should feel gentle heat penetrating deep into your skin.

Initial S+ Treatment Course:
For the first 4 weeks, treatments should be performed 3 times a week for 15-20 minutes each time. (5-7 minutes on each treatment zone)

S+ Treatment Regime:
After the first 4 weeks, as your skin grows accustomed to treatment rejuvenation results should become visible and treatments can be done once a week for 15-20 minutes, in order to maintain results.

The outcome of using S+ when following instructions correctly will reduce the appearance of fine lines and wrinkles. Optimal results can be expected 3-4 weeks after completing the recommended course of treatment.

Do not over treat. Follow the treatment regime. Overtreatment can cause redness or swelling.

Applying Treatment

Step 1: Wash face. Your skin should be clean, and free of any lotions or creams.
Step 2: Dry face thoroughly.
Step 3: Lift your S+ device from the docking station. Press and hold the Control Button (for 2 seconds). The power indicator light will turn on along with the Radio Frequency treatment indicator. The device is ready, and you may begin treatment.
Step 4: Place the treatment surface on the desired area. Apply light pressure while slowly moving the applicator in small circular motions around the face. 
Step 5: Switch to Infrared setting by pressing the control button once. Place treatment surface on the desired area of the face. The LED light will automatically activate and you will hear a low humming sound. The treatment surface temperature will slowly increase. Remove the S+ applicator from the skin if either the skin or the applicator is too hot.

Perform the treatment for 5-7 minutes on each treatment area.

IMPORTANT:
Always keep the device in motion when on your skin. Holding it stationary while treating can cause redness or mild burn.

Step 6: When you are done with your treatment, turn OFF the device by pressing and holding the control button (for 2 seconds). The indicator lights will turn off.

Step 7: Apply moisturizing cream on the treated areas after each Step 8: Clean your device and return to the docking station. Refer to Maintenance & Storage Instructions on page 15 of the manual.

HELPFUL TIP:
Make sure you hold the device steady during application and do not separate the treatment surface from your skin during treatment. This will result in a more effective treatment and more effective results.


What to Expect when Treating with S+
During an S+ session, it is normal to experience and feels the following:

  • Warmth - During the S+ session, you may feel a slight warmth. This is normal and should subside within an hour.
  • Mild red color - After each S+ session, treated areas might become visibly red (mild erythema) This is normal and should fade within 24-48 hours. Discontinue use if you encounter any discomfort or skin redness for more than 48 hours.
  • A humming noise - It is normal to hear a fan-like noise turning on and off during treatments. This is the safety feature that helps regulate the temperature during use. 
  • Possible minor skin discomfort - Your skin may become slightly irritated after using the S+. Any discomfort should disappear within 24-48 hours after treatment.


Human Skin Before Using the S+

Our skin is uneven due to wrinkles, which form over time by the breakdown of connective tissue, such as collagen and elastic fibers located in the dermis.

S+ IN ACTION

The S+ LED device emits infrared and radio frequency waves into the dermis producing new collagen and elastin for optimal anti-aging results.

Human Skin After Using the S+

With a high density of collagen and elastin fibers in the dermis, skin appears tighter with more even skin tone and youthful appearance.

NOTE!
S+ is designed for personal home use, ideally for one individual, for daily or every other day usage, much like a shaving machine or electric toothbrush. Exhaustive usage will shorten the device life and effectiveness.


The S+ device

ON & OFF / Control Button
The ON/OFF button turns the device on and off by pressing firmly for 2 seconds. Once the device is turned on, this button is used to switch between treatment options (Radiofrequency treatment and Infrared treatment) with a simple click.

Docking Station & Power Adapter
The device can be charged either when docked in the docking station with the power adapter connected, or with the power adapter directly connected to the device.
This power adapter supports AC100-240V electrical outlets. It is designed for the American standard outlet, but with the right adapter, it can fit any country's outlet.
We recommend recharging the device through the docking station.
Treatment Surface
The treatment surface is made of stainless steel. The inner cycle has 9 LEDs and the outer cycle has 16 LEDs. This surface is magnetized so it can be removed, cleaned, and snapped back into place.
There are skin contact sensors located around the treatment surface. They detect when the treatment surface is in contact with the skin. This safety feature ensures the device will work only for its purpose and preserve battery power. Once skin contact has been made, a steady red LED light (for infrared treatment) / steady blue LED light (for radio frequency treatment) will flow into the skin. Be sure to clean this surface after each treatment session, for optimal results.

More Information
Manufacturer No
Certificate Type No
Warranty Description 1 month against any manufacturing defect
Size No
Metal Type No
Brand No
Gender No
Special Event No
Style No
Diameter No
Write Your Own Review
You're reviewing:LED Anti-Aging Device
Your Rating